Kmc-controls THE-1105 Manual de usuario descargar pdf

THE-1105 1 Installation Guide

Installation Guide

Humidity Transmitter w/ Temperature Sensor

THE-1105

Mounting

Handy Box Mounting (Recommended)

1. Install,butDO NOT TIGHTEN,theHMO-

5024/5026/5030/5031mountingplatetoahandy

boxusingthetwo6-32screws(included).

2. Adjustandlevelthebackplate(inthevertical

orhorizontalplane)usingthesloedmounting

holesandtightenthetwomountingscrews.

3. RemovetheTHE-1105’scoverbyturningthetwo

setscrews(ontheside)clockwise(inward)usinga

1/16"hexwrenchuntilthecoverclearsthebase.

4. Pullallthewiresorwirecablethroughthe

backplate’sdecorativetrimplateopening

(includedwithHMO-5024/5026/5030/5031)and

throughthecableaccessholeintheTHE-1105.

5. Makesurethatthehumiditysensorisinthe

lowerrightcorner(verticalinstallation)orlower

lecorner(horizontalinstallation)ofthebase.

6. Connectthewires(seeWiringsection).

7. MounttheTHE-1105tothebackplatewiththe

two6-20x2"self-tappingscrews(included).

8. Reinstallthecoverandlockitbyturningthe

setscrewscounter-clockwise(outward).

Hollow Wall Mounting

Mountingonahollowwallupto5/8"thickcanbe

donewiththeHMO-5023orHMO-5001.Tomount

withanHMO-5023:

1. Usingthetemplate,cuta1-1/2"x2-11/16"

openinginthedrywall.

2. RemovetheTHE-1105’scoverbyturningthetwo

setscrews(ontheside)clockwise(inward)usinga

1/16"hexwrenchuntilthecoverclearsthebase.

3. LooselymounttheHMO-5023brackettothe

thermostat(coverremoved)usingthetwo6-32x

2"screws.

4. Pullthewiresthroughthewireaccessholesinthe

HMO-5023andtheTHE-1105.

5. Makesurethatthehumiditysensorisinthe

lowerrightcorner(verticalinstallation)orlower

lecorner(horizontalinstallation)ofthebase.

6. Connectthewires(seeWiringsection).

5. Insertbracketdiagonally,throughthewall

opening,centerandtightenscrews.

8. Reinstallthecoverandlockitbyturningthe

setscrewscounter-clockwise(outward).

HMO-50xx Mounting Plate

(Shown in horizontal installation)

HMO-5023 Drywall Mounting Kit

Mounting 1

Location 1

Handy Box Mounting (Recommended) 1

Hollow Wall Mounting 1

Wiring 2

Maintenance 2

More Information 2

Important Notices 2

Location

Installthesensoronaninsidewallwhereitcansense

theaverageroomtemperature/humidityandbe

awayfromdirectsunlight,heatsources,windows,

airvents,andaircirculationobstructions(curtains,

furniture,etc.).

CAUTION

Check that the

thermistor leads are

not bent and that the

thermistor bead is

upright (perpendicular

to the board) BEFORE

reinstalling the cover.

1 2

Indice de contenidos

Pagina 1 - Installation Guide

THE-1105 1 Installation GuideInstallation GuideHumidity Transmitter w/ Temperature SensorTHE-1105 MountingHandy Box Mounting (Recommended)1. Insta

Pagina 2 - More Information

Comentarios a estos manuales

Sin comentarios

Kmc-controls THE-1105 Manual de usuario

Busca en linea o descarga Manual de usuario para Sensores Kmc-controls THE-1105. KMC Controls THE-1105 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Kmc-controls THE-1105