Kmc-controls TPE-1483 Series(2008 and later) Manual de usuario descargar pdf

TPE-1483 Series Wet-Wet Differential Pressure Transducers 1 Installation Guide

Installation Guide

Wet-Wet Differential Pressure Transducers

TPE-1483 Series

Mounting 1

Plumbing 1

Wiring 2

Set-Up 2

Conﬁguration 2

Jumper Settings 2

Range 3

Bidirectional 3

Port Swap 3

Slow Damping 3

Output Reverse 3

Operation 3

Calibration 3

Maintenance 3

Mounting

Avoid locations with severe vibrations or excessive

moisture. The enclosure has a standard 1/2" conduit

opening and may be installed with either a conduit

coupler or a cable gland type ing.

1. Mount on a vertical surface with the pressure

ports on the boom.

2. Use screws in the tab holes to fasten the assembly

to the mounting surface.

3. Ensure there is enough space around the unit to

make the pressure and electrical connections.

Plumbing

NOTE: The output signal indicates a positive

value when the pressure is higher on the

High port than the Low port. As a default,

the High port is on the left and the Low

port is on the right (as shown on the circuit

board). However, a switch on the circuit

board can reverse this to correct for a

plumbing error. (See the Port Swap section

on page 3.)

1. Use appropriately rated pressure tubing for the

1/8" NPT female connections.

2. Arrange the tubing to minimize stress on the

connections.

NOTE: This document is for units available start-

ing in late 2008. See the original installation

guide available on the KMC web site for in-

stallation and conguration information on

older units with a dierent case and board.

CAUTION

Ensure that the maximum individual port

pressure does not exceed the maximum

pressure range of the unit.

WARNING

Do not use:

• In an explosive or hazardous environment.

• With combustible or ﬂammable gasses.

• As a safety or emergency stop device.

• In any other application where failure of the

product could result in personal injury.

CAUTION

Do not allow debris to get into the pressure

ports since contamination can damage the

sensor.

CAUTION

Use electrostatic discharge precautions during

installation.

114.3 mm

4.5"

64 mm

2.5"

100 mm

3.95"

Ø 0.850”

Mounting Holes

(X4) Ø 0.200”

88.9 mm

3.5"

145 mm

5.7"

1/8” NPT Female

34.93 mm

1.375"

19 mm

“Low”

Port

“High”

Port

0.75"

25.4 mm

53.98 mm

2.125"

1 2 3

Indice de contenidos

Pagina 1 - Installation Guide

TPE-1483 Series Wet-Wet Differential Pressure Transducers 1 Installation GuideInstallation GuideWet-Wet Differential Pressure TransducersTPE-1483 Se

Pagina 2 - CAUTION

TPE-1483 Series Wet-Wet Differential Pressure Transducers 2 Installation GuideWiringThis device is a 3-wire sourcing type transmier. Use 22 AWG shi

Pagina 3 - Maintenance

TPE-1483 Series Wet-Wet Differential Pressure Transducers 3 Installation GuideRangeNOTE: Range and Options switches can be changed while the unit i

Comentarios a estos manuales

Sin comentarios

Kmc-controls TPE-1483 Series(2008 and later) Manual de usuario

Busca en linea o descarga Manual de usuario para Sensores Kmc-controls TPE-1483 Series(2008 and later). KMC Controls TPE-1483 Series(2008 and later) User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Kmc-controls TPE-1483 Series(2008 and later)