Kmc-controls SAE-1162 Manual de usuario descargar pdf (Pagina 1)

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 1 Installation Guide

Installation Guide

Carbon Monoxide (CO) Detectors

SAE-1111/1112/1162

Mounting 1

SAE-1111/1112 Space Mount 1

SAE-1162 Duct Mount 1

Wiring 2

Operation 3

Warm-Up Mode 3

Normal Mode 3

Alarm Mode 3

Conﬁguration 4

Test Mode 4

Fault Mode 4

ReCal (Recalibration) Mode 4

Calibration 8

Models 9

Accessories 9

Maintenance 9

Important Notices 9

More Information 9

SAE-1111/1112 Space Mount

Install the unit at least ve feet above the nished

oor of the area to be controlled. Do not install

near doors, windows, supply air diusers of other

known air disturbances. Avoid areas prone to vibra-

tion or rapid temperature change.

1. On the mounting surface, mark and drill the four

mounting holes (for screws) and remove any

debris from all holes.

2. Aach the unit to the surface by threading four

screws through the four mounting holes.

3. Remove the two cover screws (if installed),

release the latch, and swing open the cover.

4. Insert wiring through a knockout.

5. After wiring, conguring, and testing the

unit (see later sections), close the cover and

(optionally) secure it with two (supplied) self-

tapping screws.

SAE-1162 Duct Mount

Choose a mounting location in a straight section of

a return air duct. Mount at least 5 feet (or 7.5 duct

diameters) from corners and other items that may

cause disturbances in the air ow. Avoid areas prone

to vibration or rapid temperature change.

1. Cut a 1-1/8 or 1-1/4 inch hole in the duct for the

air sampling probe.

2. Insert the probe through the hole, align the unit

so that the duct air ow is parallel with the side

vent holes in the probe (air ows directly into

the probe holes), and mark the four enclosure

mounting holes.

3. Drill the four mounting holes (for screws) and

remove any debris from all holes.

4 . Insert the sampling probe into the duct.

5. Aach the unit to the ductwork by threading four

screws through the four holes on the outside of

the enclosure.

6. Remove the two cover screws (if installed),

release the latch, and swing open the cover.

7. Insert wiring through a knockout. After wiring a

duct sensor, ll the knockout hole with plumber’s

Mounting

145 mm

5.7"

101 mm

114 mm

4.5"

89 mm

3.5"

ALARM

64 mm

2.5"

240 mm

9.5"

26 mm

177 mm

7.0"

145 mm

5.7"

101 mm

114 mm

4.5"

89 mm

3.5"

ALARM

64 mm

2.5"

SAE-1111/1112

SAE-1162

puy, caulk, or other sealant to prevent air

inltration from the conduit.

8. After wiring, conguring, and testing the

unit (see later sections), close the cover and

(optionally) secure it with two tapping screws.

1 2 3 4 5 6 7 8 9

Indice de contenidos

Pagina 1 - Installation Guide

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 1 Installation GuideInstallation GuideCarbon Monoxide (CO) Detectors SAE-1111/1112/1162 Mounting 1

Pagina 2 - CAUTION

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 2 Installation GuideUse 22 AWG shielded wiring for all connections. Do not locate device wires in

Pagina 3 - Operation

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 3 Installation GuideOperationWarm-Up Mode1. Verify that the detector is properly wired and all co

Pagina 4 - Conﬁguration

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 4 Installation Guideswitch on the front cover (or activate the remote TEST input) when the CO leve

Pagina 5

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 5 Installation GuideWhen a value is changed, press the <SAVE> key to save it to memory and a

Pagina 6 - WARNING

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 6 Installation GuidePress <MENU>Relay 2 Hyst = 20 Use the <ROLL> key to scroll throug

Pagina 7

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 7 Installation GuidePress <MENU>ReCal Md Time = 1yr This is used to set the CO sensor recal

Pagina 8 - Calibration

SAE-1111/1112/1162 Carbon Monoxide (CO) Detectors 8 Installation GuideNOTE: The sensor must be continuously powered for at least 1/2 hour prior to

Pagina 9 - Important Notices

Modelos relacionados SAE-1112 | SAE-1111 |

Comentarios a estos manuales

Sin comentarios

Kmc-controls SAE-1162 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Kmc-controls SAE-1162. KMC Controls SAE-1162 User Manual Manual de usuario

Indice de contenidos

Modelos relacionados SAE-1112 | SAE-1111 |

Comentarios a estos manuales

Kmc-controls SAE-1162 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Kmc-controls SAE-1162. KMC Controls SAE-1162 User Manual Manual de usuario

Indice de contenidos

Modelos relacionados SAE-1112 | SAE-1111 |

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Kmc-controls SAE-1162